求一个批量改孔大小的skill脚本

xlteam2

PRETTY GOOD

joeyang

thanks

yooou

有没有大神知道如何修改调取的pcell孔的大小     

yooou

dummy_tony 发表于 2020-8-21 22:10
试试看， 记得要备份。

;#######################################################

大神   不知能否通过脚本修改调取pcell孔的大小   

yangjunhui

你好，我load 这个脚本后，版图没有变化，怎么回事呢

liuliuliu320

procedure(HierSizeLayer()

let((cv winid bbox CTlist VIA1list VIA2list VIA3list VIA4list CTlist_new VIAllist_new VIA2list_new VIA3list_new)
cv=geGetEditRep ()
winid=geGetEditCellViewWindow(cv)
if(cv~>mode=="r"
then
geChangeEditMode("a")
;ifbbox=cv~>bBox
CTlist  =  leSearchHierarchy(
cv bbox 0 "rectangle" list( list( "layer" "==" list( "CA" "drawing" )) list( "width" "==" 0.22 ))
)
VIA1list=leSearchHierarchy(
cv bbox 0 "rectangle" list( list( "layer" "==" list( "V1" "drawing" )) list( "width" "==" 0.26 ))
)
VIA2list=leSearchHierarchy(
cv bbox 0 "rectangle" list( list( "layer" "==" list( "V2" "drawing" )) list( "width" "==" 0.26 ))
)
VIA3list=leSearchHierarchy(
cv bbox 0 "rectangle"  list( list( "layer" "==" list( "V3" "drawing" )) list( "width" "==" 0.26 ))
)
foreach (x CTlist
leSizeShape(x -0.065)
); foreach
foreach (x VIA1list
leSizeShape(x - 0.08)
);foreach
foreach(x VIA2list
leSizeShape (x - 0.08)
);foreach
foreach (x VIA3list
leSizeShape(x - 0.08)
);foreach
CTlist_new    =leSearchHierarchy (
cv bbox  32 "rectangle" list( list( "layer" "==" list( "CA" "drawing" )) list( "width" "==" 0.22 ))
)
VIA1list_new=leSearchHierarchy(
cv bbox  32 "rectangle"  list( list( "layer" "==" list( "V1" "drawing" )) list( "width" "==" 0.26 ))
)
VIA2list_new=leSearchHierarchy(
cv bbox 32 "rectangle"   list( list( "layer" "==" list( "V2" "drawing" )) list( "width" "==" 0.26 ))
)
VIA3list_new=leSearchHierarchy(
cv bbox 32 "rectangle"   list(list( "layer" "=="  list( "V3" "drawing" )) list( "width" "==" 0.26))
)
geSave ()
instances=filtercell(cv~>instances)
foreach (x instances
geEditInPlace (winid "a" x 0 1 1)
HierSizeLayer()
leReturn()
); foreach
);let
);procedure
procedure(filtercell(objs)
let ( (namelist num nameflag objs_new)
namelist=artUnique (objs~>cellName)
num=length(namelist)
declare (group [num])
nameflag=listToVector(namelist)
objs_new=nil
for(i 0 num-1
group=setof(x objs x->cellName==nameflag)
objs_new=cons (car(group ) objs_new)
); for
reverse (objs_new)
);let
);procedure

liuliuliu320

liuliuliu320 发表于 2022-8-26 18:26
procedure(HierSizeLayer()let((cv winid bbox CTlist VIA1list VIA2list VIA3list VIA4list CTlist_new VI ...

这个可以从顶层修改底层所有的孔

bj_donnyh

liuliuliu320 发表于 2022-8-26 18:26
procedure(HierSizeLayer()

let((cv winid bbox CTlist VIA1list VIA2list VIA3list VIA4list CTlist_new  ...

instances=filtercell(cv~>instances)   ----- 这行可以删掉
foreach (x instances    ---- 这行可替换成 ----

foreach (x cv~>instances