提取寄生参数是怎么才能不把大管子拆开啊

ji_yan_li

我用rcxt提取计生参数，可是原来的网表是：
M0 Y net7 GND GND N_18_G2 l=0.18u w=12u
M1 VDD net7 Y VDD P_18_G2 l=0.18u w=17.98u
M2 net7 A GND GND N_18_G2 l=0.18u w=4.8u
M3 VDD A net7 VDD P_18_G2 l=0.18u w=7.12u
提完参数就变成了：
[email=MM3@2]MM3@2[/email] VDD [email=M3@2:g]M3@2:g[/email] net7 VDD P_18_G2 L=0.183825u W=1.78213u
[email=MM2@2]MM2@2[/email] net7 [email=M2@2:g]M2@2:g[/email] GND GND N_18_G2 L=0.18567u W=1.20213u
[email=MM3@3]MM3@3[/email] VDD [email=M3@3:g]M3@3:g[/email] net7 VDD P_18_G2 L=0.183825u W=1.78213u
[email=MM2@3]MM2@3[/email] net7 [email=M2@3:g]M2@3:g[/email] GND GND N_18_G2 L=0.18567u W=1.20213u
[email=MM3@4]MM3@4[/email] VDD [email=M3@4:g]M3@4:g[/email] net7 VDD P_18_G2 L=0.183825u W=1.78213u
[email=MM2@4]MM2@4[/email] net7 [email=M2@4:g]M2@4:g[/email] GND GND N_18_G2 L=0.18567u W=1.20213u
MM3 VDD M3:g net7 VDD P_18_G2 L=0.183825u W=1.78213u
MM2 net7 M2:g GND GND N_18_G2 L=0.18567u W=1.20213u
[email=MM1@2]MM1@2[/email] VDD [email=M1@2:g]M1@2:g[/email] Y VDD P_18_G2 L=0.183583u W=1.90213u
[email=MM0@2]MM0@2[/email] Y [email=M0@2:g]M0@2:g[/email] GND GND N_18_G2 L=0.184932u W=1.38213u
[email=MM1@3]MM1@3[/email] VDD [email=M1@3:g]M1@3:g[/email] Y VDD P_18_G2 L=0.183583u W=1.90213u
[email=MM0@3]MM0@3[/email] Y [email=M0@3:g]M0@3:g[/email] GND GND N_18_G2 L=0.184932u W=1.38213u
[email=MM0@4]MM0@4[/email] Y [email=M0@4:g]M0@4:g[/email] GND GND N_18_G2 L=0.184932u W=1.38213u
[email=MM1@4]MM1@4[/email] VDD [email=M1@4:g]M1@4:g[/email] Y VDD P_18_G2 L=0.183583u W=1.90213u
[email=MM0@5]MM0@5[/email] Y [email=M0@5:g]M0@5:g[/email] GND GND N_18_G2 L=0.184932u W=1.38213u
[email=MM1@5]MM1@5[/email] VDD [email=M1@5:g]M1@5:g[/email] Y VDD P_18_G2 L=0.183583u W=1.90213u
[email=MM0@6]MM0@6[/email] Y [email=M0@6:g]M0@6:g[/email] GND GND N_18_G2 L=0.184932u W=1.38213u
[email=MM1@6]MM1@6[/email] VDD [email=M1@6:g]M1@6:g[/email] Y VDD P_18_G2 L=0.183583u W=1.90213u
[email=MM0@7]MM0@7[/email] Y [email=M0@7:g]M0@7:g[/email] GND GND N_18_G2 L=0.184932u W=1.38213u
[email=MM1@7]MM1@7[/email] VDD [email=M1@7:g]M1@7:g[/email] Y VDD P_18_G2 L=0.183583u W=1.90213u
[email=MM0@8]MM0@8[/email] Y [email=M0@8:g]M0@8:g[/email] GND GND N_18_G2 L=0.184932u W=1.38213u
[email=MM1@8]MM1@8[/email] VDD [email=M1@8:g]M1@8:g[/email] Y VDD P_18_G2 L=0.183119u W=1.89385u
[email=MM0@9]MM0@9[/email] Y [email=M0@9:g]M0@9:g[/email] GND GND N_18_G2 L=0.184932u W=1.38213u
[email=MM1@9]MM1@9[/email] VDD [email=M1@9:g]M1@9:g[/email] Y VDD P_18_G2 L=0.183583u W=1.90213u
MM0 Y M0:g GND GND N_18_G2 L=0.18u W=0.96u
[email=MM1@10]MM1@10[/email] VDD [email=M1@10:g]M1@10:g[/email] Y VDD P_18_G2 L=0.183119u W=1.89385u
MM1 VDD M1:g Y VDD P_18_G2 L=0.18u W=0.9u
应该是把大管子按版图的尺寸拆开了吧。
有大侠知道该怎么解决么

keroppi

我只知道 Calibre   抽取有三個選項  其中一個 Lump的選項  就不會把大管子拆開