|
|
马上注册，结交更多好友，享用更多功能，让你轻松玩转社区。
您需要 登录 才可以下载或查看，没有账号？注册
x
書名 : RF circuit design
作者: Richard C. Li
出版日期: 2009
作者簡介:
Education : 1977-1980 PhD Student Electrical Engineering (Dept. of E E, Pennsylvania State University State College)
Experience:
1979-1984 Staff Engineer (MOTOROLA Communication Division)
1984-1985 System Engineer DBS System, Consumer Product (Texas Instruments)
1985-1987 Senior Staff Engineer Satellite Communication System (RCA Astro-Electronics)
1987-1998 Principal Staff Engineer. RF Technology Center, Radius Radio (MOTOROLA Communication Division)
1998-1998 Sr. Principal Staff Engineer. Consumer System Group (MOTOROLA SPS Sector)
1998-2001 Sr. Principal Staff Engineer. Messaging System Product Group (MOTOROLA MSPG Group)
2001-2004 Sr. Technical Consultant RFIC R&D group (Winbond Integrated Circuit Co.)
內容簡介:
This book targets the two most difficult skills facing RF/RFIC designer: impedance matching and RF/RFIC grounding.
The content is divided into five key parts:
1. Impedance Matching (chapters 1-6)
2. RF/AC Grounding (chapters 7-8)
3. Main Electrical Parameters of a RF Block (chapters 9-11)
4. Individual RF Block Circuit Design (chapters 12-19)
5. RF System Engineering (chapters 20-22)
The selection, organization, and treatment of the subjects in this book are quite different from other books related to RF/RFIC design. The objective of the book is to enable RF circuit designers to master the correct methodology of RF circuit design. The readers are assumed to be familiar with the basic theory of RF circuit design. In addition to the unique content order, this book has some very practical design schemes that are introduced and recommended in many sections. Parts 3-5 address topics similar to other references published to date. However, the author has made many attempts to better clarify important concepts. This includes the addition of special circuit topologies and introduction of some useful schemes for simulation and layout.
In addition to the individual RF blocks' description and analysis, the main design technologies emphasized in this book include impedance matching, RF grounding, single-ended stages to different pairs, jeopardy in RFIC design, etc., in effect making the configuration of this book both longitudinal and transversal.
PREFACE.
PART I INDIVIDUAL RF BLOCKS.
1. LNA (LOW NOISE AMPLIFIER).
1.1 Introduction.
2. MIXERS.
3. DIFFERENTIAL PAIRS.
4. RF BALUN.
5. TUNABLE FILTERS.
6. VCO (VOLTAGE-CONTROLLED OSCILLATOR)
7. POWER AMPLIFIERS (PA).
PART II DESIGN TECHNOLOGIES AND SCHEMES.
8. DIFFERENT METHODOLOGY BETWEEN RF AND DIGITAL CIRCUIT DESIGN.
9. VOLTAGE AND POWER TRANSPORTATION.
10. IMPEDANCE MATCHING IN NARROW-BAND CASE.
11. IMPEDANCE MATCHING IN A WIDE-BAND CASE.
12. IMPEDANCE AND GAIN OF A RAW DEVICE.
13. IMPEDANCE MEASUREMENT. .
Appendices.
References.
14. GROUNDING.
15. EQUIPOTENTIALITY AND CURRENT COUPLING ON THE GROUND SURFACE.
16. RFIC (RADIO FREQUENCY INTEGRATED CIRCUIT) AND SOC  (SYSTEM ON CHIP).
17. MANUFACTURABILITY OF PRODUCT DESIGN.
PART III RF SYSTEM ANALYSIS.
18. MAIN PARAMETERS AND SYSTEM ANALYSIS IN RF CIRCUIT DESIGN.
Appendices.
References
Wiley.RF.Circuit.Design.Dec.2008.eBook-DDU.part1.rar
(4 MB, 下载次数: 628 )
[ 本帖最后由 tjumicrosoft 于 2009-5-1 00:27 编辑 ] |
|
/2 
eetop公众号
创芯大讲堂
创芯人才网
发表于 2009-4-30 02:59:31
楼主
